One resin cast Anubis Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock face mask, robot skull head, and cowl.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with laurel detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Khopesh Chain Weapon.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. Please view the other listing for parts related to Armiger sized knights.
This weapon replaces the stock chain weapon from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply attach this weapon as you would the stock chain weapon from the kit.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Spartan Knight Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Death Guardian Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast frosted clear Plasma Coil Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace. You can also add an LED bulb to backlight the clear plastic.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with banner detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One Iron Wolf Conversion Kit which includes:
- Iron Wolf Head
- Iron Wolf Shoulder Pad (Right)
- Iron Wolf Shoulder Pad (Left)
- Iron Wolf Frost Cannon
- A set of Iron Wolf Knee Pads
- Iron Wolf Feet

This kit is sold at a discount to buying all parts individually.

NOTE: Some parts are cast resin, others are 3D printed.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock head, shoulder pads, knee pads, thermal cannon, and feet.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model. Note that the shoulder pads ARE NOT interchangeable: the right shoulder pad will only fit the right shoulder and the left shoulder pad will only fit the left shoulder.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Mechanic Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One Custodian Guard Conversion Kit which includes:
- Custodian Guard Face Plate (choice of with or without cut eye holes)
- Custodian Guard Shoulder Pad (Plain)
- Custodian Guard Shoulder Pad (Banner)
- Eagle Claws
- Custodian Guard Crotch Plate
- Set of Custodian Guard Hip Plates
- Set of Custodian Guard Knee Fan Plates
- Set of Custodian Guard Shin Plates
- Set of Custodian Guard Toe Guards

This kit is sold at a discount to buying all parts individually.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces replace the stock face plate, shoulder pads, fingers, shin plates, knee pads, and crotch plate.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model. For detailed attaching instructions please visit the component's product page. Note that the shoulder pads are interchangeable (they can be used on either left or right side).



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set containing two 3D printed Custodian Guard Toe Guards.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces do not replace any existing component, but are rather accents to the model's toes.
NOTE: This kit includes 2 toe guards. If you would like to apply a toe guard to all of the model's toes please buy 4 sets.

ATTACHING INSTRUCTIONS
Simply glue this toe guard onto the FRONT toe of the stock kit. If purchasing multiple sets, glue a toe guard to each of the model's toes.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of left and right 3D printed Custodian Guard Hip Plates.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces do not replace any existing component, but are rather accents to the model's hips.

ATTACHING INSTRUCTIONS
1) Simply glue these Hip Plates onto the top of the ball joints that make up the model's hip areas.
2) The riveted edge of each plate should face AWAY from the model.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of two resin cast Custodian Guard Shin Plates.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces replace the stock shin plates and knee pads from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue each Shin Plate into place on the leg where the stock shin plate and knee pad would normally go.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Iron Wolf Head with wire bundle.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock face mask, robot skull head, and cowl.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set containing two 3D printed Custodian Guard Knee Fan Plates.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights.
These pieces do not replace any existing component, but are rather accents to the model's knees.
NOTE: These components will interfere with the Questoris kit's stock knee pads, so please use the Custodian Guard Shin Plates if you plan to use these pieces.

ATTACHING INSTRUCTIONS
Simply glue the Knee Fan Plates to the outside (or inside) of each leg.
This part frames the large hinge point that makes up the knee joint.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Eagle Claws (3 fingers and a thumb).

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These claws replace the stock fingers included with the kit.

ATTACHING INSTRUCTIONS
1) Simply glue the three fingers where the existing fingers normally go.
2) Pop the thumb into the ball jointed area where the existing thumb normally goes.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Armored Torso Extension Unit.

COMPATIBILITY
This accessory component is compatible with all Questoris and Dominus class Knights.
This part does not replace any existing component, but rather is sandwiched between the legs and torso of the model to make it taller.

ATTACHING INSTRUCTIONS
1) Glue the torso extender to the top of the ball located on top of the model's legs.
2) You can glue a magnet of up to 5mm in diameter into the hole on the top of the extender in order to magnetize the legs to the bottom of the main body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Bulk Head Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Custodian Guard crotch plate.

COMPATIBILITY
This component is compatible ONLY with Questoris class Knights.
This plate replaces the stock crotch plate that comes with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this plate onto the crotch as you would the stock plate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Custodian Guard Shoulder Pad with banner detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.