One resin cast Anubis Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock face mask, robot skull head, and cowl.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Shoulder Pad Hollow Arch Vents (4 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with Dominus class Knights.
These parts do not replace any existing component, but rather are glued onto the shoulder pads.

ATTACHING INSTRUCTIONS
1) Arrange a number of Arch Vents onto the shoulder pad (maximum of 4 per pad), resting the flat bottom on top of the shoulder pad's trim.
2) Glue in place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Shoulder Pad Arch Vents with skull details (4 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with Dominus class Knights.
These parts do not replace any existing component, but rather are glued onto the shoulder pads.

ATTACHING INSTRUCTIONS
1) Arrange a number of Arch Vents onto the shoulder pad (maximum of 4 per pad), resting the flat bottom on top of the shoulder pad's trim.
2) Glue in place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Shoulder Pad Arch Vents with slat details (4 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with Dominus class Knights.
These parts do not replace any existing component, but rather are glued onto the shoulder pads.

ATTACHING INSTRUCTIONS
1) Arrange a number of Arch Vents onto the shoulder pad (maximum of 4 per pad), resting the flat bottom on top of the shoulder pad's trim.
2) Glue in place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Armored Torso Extension Unit.

COMPATIBILITY
This accessory component is compatible with all Questoris and Dominus class Knights.
This part does not replace any existing component, but rather is sandwiched between the legs and torso of the model to make it taller.

ATTACHING INSTRUCTIONS
1) Glue the torso extender to the top of the ball located on top of the model's legs.
2) You can glue a magnet of up to 5mm in diameter into the hole on the top of the extender in order to magnetize the legs to the bottom of the main body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Battle Shield.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This shield replaces the stock shield options which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this shield into place as you would the stock shield.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Claw Cover (available in Left or Right). Photos on model shown only for compatibility purposes.

WARNING! This conversion is not for the feint of heart! It involves purchasing parts from another manufacturer, and heavily modifying BOTH miniatures! This cover does NOT fit the fist that arrives stock with the Titan kit, as it is far too large!

COMPATIBILITY
This component is compatible with all Questoris class Knights, only when used in conjunction with DreamForge-Games 28mm Left or Right Handed Mauler Claw.
This part does not replace any stock part, instead the stock chain-weapon end must be cut off, and the new claw hand grafted into place.

ATTACHING INSTRUCTIONS
This conversion is not for the faint of heart. Without heavy modification, this 3D printed component is not helpful!
1) You must have a Left or Right Handed Mauler Claw.
2) Cut the end off the stock chain-weapon.
3) Modify the wrist of the Mauler Claw so it may be grafted onto the stump of the chain-weapon.
4) Glue the claw cover onto the back of the claw hand.
Click here to see a great photo example from a customer on how to complete this conversion.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Blood Guardian Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with banner detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with laurel detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Bulk Head Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Cartouche Shield.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This shield replaces the stock shield options which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this shield into place as you would the stock shield.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Chaos Spikes Shoulder Pad.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Chaos Star Crotch Banner.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This hanging chain detail replaces the stock long banner & chain which is suspended between the model's legs.

ATTACHING INSTRUCTIONS
Simply glue the ends of the chain to where the stock banner slots into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Cog Crotch Banner.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This hanging chain detail replaces the stock long banner & chain which is suspended between the model's legs.

ATTACHING INSTRUCTIONS
Simply glue the ends of the chain to where the stock banner slots into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Cog Crotch Banner with filled hole.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This hanging chain detail replaces the stock long banner & chain which is suspended between the model's legs.

ATTACHING INSTRUCTIONS
Simply glue the ends of the chain to where the stock banner slots into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Cog Shield.

COMPATIBILITY
This accessory component is compatible with Questoris class Knights.
This shield replaces the stock shield options which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this shield into place as you would the stock shield.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set with two 3D printed Cog styled Shoulder Pad Toppers.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. These parts do not replace any existing component, but rather add detail to the top arch of the stock plastic shoulder pads.

ATTACHING INSTRUCTIONS
Position the Pad Toppers on the flat vertical face of each shoulder pad, so the side with the twin-riveted teeth face out, and away from the knight's body (glueing the Pad Topper on the other way will not allow the shoulder pad to be installed).
Make sure it is positioned so that the Pad Toppers fill in the gap between the shoulder pad and the carapace armor, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One Custodian Eagle Conversion Kit which includes:
- Eagle Head
- Custodian Guard Shoulder Pad (Plain)
- Custodian Guard Shoulder Pad (Banner)
- Eagle Claws
- Custodian Guard Crotch Plate
- Set of Custodian Guard Hip Plates
- Set of Custodian Guard Knee Fan Plates
- Set of Custodian Guard Shin Plates
- Set of Custodian Guard Toe Guards

This kit is sold at a discount to buying all parts individually.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces replace the stock head, shoulder pads, fingers, shin plates, knee pads, and crotch plate.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model. For detailed attaching instructions please visit the component's product page. Note that the shoulder pads are interchangeable (they can be used on either left or right side).



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One Custodian Guard Conversion Kit which includes:
- Custodian Guard Face Plate (choice of with or without cut eye holes)
- Custodian Guard Shoulder Pad (Plain)
- Custodian Guard Shoulder Pad (Banner)
- Eagle Claws
- Custodian Guard Crotch Plate
- Set of Custodian Guard Hip Plates
- Set of Custodian Guard Knee Fan Plates
- Set of Custodian Guard Shin Plates
- Set of Custodian Guard Toe Guards

This kit is sold at a discount to buying all parts individually.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights.
These pieces replace the stock face plate, shoulder pads, fingers, shin plates, knee pads, and crotch plate.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model. For detailed attaching instructions please visit the component's product page. Note that the shoulder pads are interchangeable (they can be used on either left or right side).



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.