Iron Wolf Minis

One 3D printed Mini Octopus Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Dragon Scale Shoulder Pad. This listing is for a single shoulder pad, for both left and right shoulder, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Armiger class Knights.
This shoulder pad replaces the stock shoulder pad on either side of the model.

ATTACHING INSTRUCTIONS
Simply glue the shoulder pad in place, where the stock shoulder pad normally sits. This shoulder pad can fit onto either side of the body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Bull Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Shark Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Demon Skull Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Hammerhead Shark Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Anubis Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock face mask, robot skull head, and cowl.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with laurel detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Khopesh Chain Weapon.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. Please view the other listing for parts related to Armiger sized knights.
This weapon replaces the stock chain weapon from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply attach this weapon as you would the stock chain weapon from the kit.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Spartan Knight Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Death Guardian Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast frosted clear Plasma Coil Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace. You can also add an LED bulb to backlight the clear plastic.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Blood Guardian Shoulder Pad with banner detail.
This shoulder pad can fit on either side of the model. If you would like one shoulder pad for each side of the model, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights. This shoulder pad replaces the stock shoulder pad included with the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this shoulder pad on the model's shoulder, as you would the stock shoulder pad.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One Iron Wolf Conversion Kit which includes:
- Iron Wolf Head
- Iron Wolf Shoulder Pad (Right)
- Iron Wolf Shoulder Pad (Left)
- Iron Wolf Frost Cannon
- A set of Iron Wolf Knee Pads
- Iron Wolf Feet

This kit is sold at a discount to buying all parts individually.

NOTE: Some parts are cast resin, others are 3D printed.

COMPATIBILITY
These accessory components are compatible ONLY with Questoris class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock head, shoulder pads, knee pads, thermal cannon, and feet.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model. Note that the shoulder pads ARE NOT interchangeable: the right shoulder pad will only fit the right shoulder and the left shoulder pad will only fit the left shoulder.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Mechanic Carapace Hatch.

COMPATIBILITY
This accessory component is compatible ONLY with Questoris class Knights.
This carapace hatch replaces the stock carapace hatch from the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue the hatch where the existing hatch normally sits, on the top of the main carapace.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Armored Torso Extension Unit.

COMPATIBILITY
This accessory component is compatible with all Questoris and Dominus class Knights.
This part does not replace any existing component, but rather is sandwiched between the legs and torso of the model to make it taller.

ATTACHING INSTRUCTIONS
1) Glue the torso extender to the top of the ball located on top of the model's legs.
2) You can glue a magnet of up to 5mm in diameter into the hole on the top of the extender in order to magnetize the legs to the bottom of the main body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Torso Extension Unit. This piece comes in 2 parts (domed base and outer disk with pistons).

COMPATIBILITY
This accessory component is compatible with all Questoris and Dominus class Knights.
This part does not replace any existing component, but rather is sandwiched between the legs and torso of the model to make it taller.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
1) Combine both parts by gluing the outer disk with pistons to the domed base.
2) Glue the combined torso extender to the top of the ball located on top of the model's legs.
3) You can glue a magnet of up to 5mm in diameter into the hole on the top of the extender in order to magnetize the legs to the bottom of the main body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Anubis Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights. Please view the other listing for parts related to Armiger sized knights.
These pieces replace the stock face mask, robot skull head, and cowl.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set containing two 3D printed Custodian Guard Knee Fan Plates.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights.
These pieces do not replace any existing component, but are rather accents to the model's knees.
NOTE: These components will interfere with the Questoris kit's stock knee pads, so please use the Custodian Guard Shin Plates if you plan to use these pieces.

ATTACHING INSTRUCTIONS
Simply glue the Knee Fan Plates to the outside (or inside) of each leg.
This part frames the large hinge point that makes up the knee joint.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Spartan Knight Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Eagle Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights.
These pieces replace the stock face mask, robot skull head, and cowl.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Shoulder Pad Arch Vents with skull details (4 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with Dominus class Knights.
These parts do not replace any existing component, but rather are glued onto the shoulder pads.

ATTACHING INSTRUCTIONS
1) Arrange a number of Arch Vents onto the shoulder pad (maximum of 4 per pad), resting the flat bottom on top of the shoulder pad's trim.
2) Glue in place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Death Guardian Face Plate.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mirror Mask.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This mask replaces the stock masks which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this mask onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Dragon Scale Shoulder Pad. This listing is for a single shoulder pad, for both left and right shoulder, please purchase two.

COMPATIBILITY
This accessory component is compatible ONLY with Armiger class Knights.
This shoulder pad replaces the stock shoulder pad on either side of the model.

ATTACHING INSTRUCTIONS
Simply glue the shoulder pad in place, where the stock shoulder pad normally sits. This shoulder pad can fit onto either side of the body.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Hammerhead Shark Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Shark Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Demon Skull Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Octopus Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Armadillo Carapace.

COMPATIBILITY
This accessory component is compatible ONLY with Armiger class Knights.
This armored carapace replaces the stock carapace included with the kit.

ATTACHING INSTRUCTIONS
1) Butt the carapace up against the back of the stock cowl for best alignment.
2) Center the armor side-to-side on top of the main body, and then glue it into position.
3) Glue the shoulder pads and gun into place on top of the carapace.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Bull Head & Cowl.

COMPATIBILITY
These accessory components are compatible ONLY with Armiger class Knights.
This head and cowl replace the stock head and cowl.

ATTACHING INSTRUCTIONS
WARNING! This head will NOT fit inside the standard cowl which is provided with the kit, as it is far too tight!
1) Glue the cowl into place, where the normal cowl would usually sit.
2) Insert the peg on the top of the head into the hole on the underside of the carapace armor, similar to how the standard kit should be built.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners. 
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Mini Siege Saw.

COMPATIBILITY
This accessory component is compatible ONLY with Armiger class Knights.
This weapon replaces the standard chain weapon supplied with the kit, and can be used on either side of the model.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
1) Clip the curved wire from the back of the arm of the stock model (see photo).
2) Glue the halves of the lower arm of the stock model together, with the new weapon sandwiched between them.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Mini Torso Extension Unit.

COMPATIBILITY
This accessory component is compatible with ONLY Armiger class Knights. Please view the other listing for parts related to full sized knights.
This part does not replace any existing component, but rather is sandwiched between the legs and torso of the model to make it taller.

ATTACHING INSTRUCTIONS
Glue the extender to the bottom of the torso, so the rear piston ends sandwich the cylindrical detail near the back of the model.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed set of 3 Miniature Scale Wolf Conversion Kits which includes:
- Miniature Scale - Wolf Heads (3 pcs)
- Miniature Scale - Wolf Claws (3 pcs - Left)
- Miniature Scale - Frost Cannons (3 pcs)
- Miniature Scale - Wolf Feet (3 pairs)

This kit is sold at a discount to buying all parts individually.

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights. Please view the other listing for parts related to full scale Questoris knights.
These pieces replace the stock head, chain weapon, ranged weapon, and feet.

ATTACHING INSTRUCTIONS
Each component will fit exactly where its stock counterpart should go on the model.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Miniature Scale Wolf Heads (3 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights. Please view the other listing for parts related to full scale Questoris knights.
These pieces replace the stock head and cowl from the kit.

ATTACHING INSTRUCTIONS
Simply insert the peg on the top of the head, into the hole on the underside of the Knight's carapace armor, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Miniature Scale Khopesh Chain Weapons (3 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights. Please view the other listing for parts related to full scale Questoris knights.
These pieces replace the stock chain weapons from the kit.

ATTACHING INSTRUCTIONS
Simply align the top of the elbow joint with the lower portion of the stock arm, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Miniature Scale Torso Extenders (3 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights. Please view the other listing for parts related to full scale Questoris knights.
These pieces do not replace any stock piece, but are instead sandwiched between the torso and legs of the model to make it taller.

ATTACHING INSTRUCTIONS
Simply sandwich this component between the main body and the top of the legs, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Miniature Scale Wolf Feet (3 pairs).

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights. Please view the other listing for parts related to full scale Questoris knights.
These pieces replace the stock feet from the kit.

ATTACHING INSTRUCTIONS
Simply position each foot onto the bottom of the legs, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Miniature Scale Photon Colliders (3 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with TITANICUS SCALE Questoris Knights.
These pieces replace the stock ranged weapon from the kit.

ATTACHING INSTRUCTIONS
Simply fit the back of the gun into the front of the gun arm, and glue into place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.