One 3D printed Panther Head with wire bundle.

COMPATIBILITY
These accessory components are compatible with Questoris and Dominus class Knights.
These pieces replace the stock face mask, robot skull head, and cowl.

ATTACHING INSTRUCTIONS
1) Glue the wire bundle to the section where the head is normally attached.
2) I have designed the head to swivel, and be removable by using small magnets.
3) I have included the link to these magnets here. Two of these small 3mm magnets are required.
4) The two small pipes that normally link to the front of the skull head can be glued onto this replacement head instead.
5) You can also glue the head in place and skip the magnets completely, though it WILL NOT rotate.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Iron Prow Rebreather. This mask covers only the bottom portion of the skull head, leaving the eyes and upper skull exposed.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This mask replaces the stock mask & pipes which come with the stock kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this mask onto the front of the skull head as you would the stock mask. This mask includes special pipes which replace the stock pipes normally glued to the sides of the skull head.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One 3D printed Death Guardian Plague Mask.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This face plate replaces the stock masks which are included in the kit.

ATTACHING INSTRUCTIONS
Simply glue this face plate onto the front of the skull head as you would the stock mask.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Studs - Pyramids (10 pieces).

COMPATIBILITY
These accessory components are compatible with all Questoris and Dominus class Knights.
These parts do not replace any existing component, and can be glued anywhere you would like to add extra detail / flair.

ATTACHING INSTRUCTIONS
The underside of these studs have a concave shape, so they will fit on most rounded surfaces of the model. The bottoms can be sanded in order to fit better onto flatter areas. Mounting these details onto some complex surfaces will require sanding and fitting for a flush fit.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One resin cast Vassal Rebreather. This mask covers only the bottom portion of the skull head, leaving the eyes and upper skull exposed.

COMPATIBILITY
This accessory component is compatible with Questoris and Dominus class Knights.
This mask replaces the stock mask & pipes which come with the stock kit.

CLEANING INSTRUCTIONS
Add some drops of dish soap to a cup of warm water and stir. Place the component(s) into the soapy water and leave to soak for 5-10 minutes, then thoroughly scrub each piece with an OLD toothbrush. Rinse component(s) thoroughly and allow to dry.

ATTACHING INSTRUCTIONS
Simply glue this mask onto the front of the skull head as you would the stock mask. This mask includes special pipes which replace the stock pipes normally glued to the sides of the skull head.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Studs - Spikes (10 pieces).

COMPATIBILITY
These accessory components are compatible with all Questoris and Dominus class Knights.
These parts do not replace any existing component, and can be glued anywhere you would like to add extra detail / flair.

ATTACHING INSTRUCTIONS
The underside of these studs have a concave shape, so they will fit on most rounded surfaces of the model. The bottoms can be sanded in order to fit better onto flatter areas. Mounting these details onto some complex surfaces will require sanding and fitting for a flush fit.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.

One set of 3D printed Shoulder Pad Hollow Arch Vents (4 pieces).

COMPATIBILITY
These accessory components are compatible ONLY with Dominus class Knights.
These parts do not replace any existing component, but rather are glued onto the shoulder pads.

ATTACHING INSTRUCTIONS
1) Arrange a number of Arch Vents onto the shoulder pad (maximum of 4 per pad), resting the flat bottom on top of the shoulder pad's trim.
2) Glue in place.



DISCLAIMERS
This web store is completely unofficial, and its contents are in no way endorsed, or affiliated with Games Workshop Limited. Imperial Knight Dominus Valiant, Imperial Knight Dominus Castellan, Imperial Knight Titan, Imperial Knight Warden, Imperial Knight Paladin, Imperial Knight Errant, Imperial Knight Crusader, Imperial Knight Gallant, Armiger Warglaive, Titanicus and the Warhammer 40,000 name are either ® or ™, and/or © Games Workshop Limited, variably registered around the world. Photographs of existing miniature kits are used only to show scale and compatibility with the accessories found on this page. Used without permission. No challenge to their status intended. All Rights Reserved to their respective owners.
Choking hazard. Not meant for children 18 years or younger.
These custom designed conversion components will arrive unpainted.